Truck Drive Shaft Puller

By Michael 14 Oct, 2020

Hydraulic wheel hub puller for cardan shafts / drive shafts 10 tons. Drive shaft removal post by gunmetal 2 » fri jul 14, 2017 1:58 am to get the coupler and shaft apart you have to heat the coupler cherry red and then us a flat bar and hammer a big hammer.

Pin on DIY Projects

Slide hammer and bearing puller set, 5 pc.

Truck drive shaft puller. Chock front wheels and safely position rear of truck so tires are off the ground. Truck truck cargo control recovery medium duty heavy duty load securing view all winch centre accessories ac powered. Placing a wood block over the bushing end and tap into the drive shaft housing (torque tube) with a hammer.

When removing an older vehicle drive shaft use electrical tape to wrap around the u joint cups so they don't fall off and release the cup needle bearings. Additional adapter sets also available reduces the risk of damage to Put transmission in neutral and release parking brake.

Universal dummy drive shaft wheel bearing supports are easy to install, and allow most light vehicles to be placed back on their wheels, and moved without their drive shafts. Tool used to seperate the drive shaft bushing seal from the drive shaft. To drive off the coupler from the shaft.

You will have to clamp the one shaft down so when you hit the coupler the shaft stay's in place. For instance, when the gearbox / engine are removed, and the vehicle needs to be moved. Hit the axle harder and more accurately without stud damage or flying metal fragments.

To install simply insert in place of the drive shaft through the wheel drive flange. Otc 7075 transmission output shaft end yoke remover 1610 1710 1760 1810 series $115.94. This will require a bushing puller.

Slide hammer and puller set, 14 pc. For 1929 1930 1931 1932 1933 1934 1935 1936 1937. Tiger tool 10903 heavy duty universal hub puller.

A paint stick works great. Add to cart add to my list. Procedure to replace center bearing (cb) on a 2006 dc sr5 4x4 without removing drive shaft from the truck.

Tiger tool 11001 axle shaft puller. Easily remove drive axles quickly with this axle shaft removal tool. Bosch automotive service solutions 28635 mound road, warren, mi 48092 usa.

Jdg1560 drive gear puller plate tool. Fully adjustable pulling arms and stud adapters are quick and easy to install Check the torque tube drive shaft bushing for wear.

Hydraulic spindle with a maximum of 10 tons of pressure. Additional adapter sets also available This tool is used on 6059 and 6068 engines superseded from jdg670a

At this point the back half of the shaft will be free so hang onto it. Special pullers can be rented. Choose from three different sizes to fit the main bearing tube id:

They have these pullers made. This tool is used to remove the drive gear from the db2, db4 and de10 fuel injection pump drive shaft, to allow removal of the pump. On some cars there will be a center support which must be undone by removing the two center support mounting bolts.

Performance tool w89742 at $195.99. Slide hammer and bearing puller set, 5 pc. Hydraulic spindle up to 10 tons, can be operated with ratchet or manually.

Fully adjustable pulling arms and stud adapters are quick and easy to install; Automotive light truck u joint puller manufacturers part #: Constructed from heavy duty cast steel, this bearing puller set works on most domestic cars.

This bushing is located at the front of the torque tube where the rear yoke slides into the tube. Chevy truck parts | chevrolet truck parts. Slide hammer and puller set, 14 pc.

With the tiger tool axle shaft puller you can easily remove even the most seized axle shaft in minutes. Compare $149.99 bearing race and seal driver sku: Put a mark on the flanges located just behind the cb.

Hydraulic wheel hub drive press shaft puller 10 ton power 4 and 5 stud hubs bolt.

How to Measure Towing Capacity, GVWR, GCWR Towing 101 in